Using Shutter Module 4C 5 A to control shutters with multiple buttons
Don't know how to make your home shutters smart? Freedompro Shutter Module is the perfect solution to make your home motorized shutters smart and manage them using multiple buttons.
Warnings
Please read the following warnings carefully before proceeding:
The installation of the device should be done carefully by a qualified electrician.
Any changes to the wiring should be made only after ensuring that there is no voltage in the electrical system.
Install the device in a protected, dry environment and inside the building.
Do not connect devices that exceed the maximum load indicated to the module.
Install the module only on electrical grids and devices that comply with current standards.
A short circuit in the power grid or in any device connected to the module may damage it.
Connect the module only as indicated in this manual. Any other method may cause damage and void the warranty.
Install on the AC side of the device a 20 A circuit breaker with an impulse withstand voltage (Uimp) of at least 4 kV and compatible voltage rating.
The device can be connected with heat-resistant (not less than 105 °C) 18-12 AWG solid conductor wires.
Neutral fuse: Disconnect mains power before servicing.
Follow the wiring diagram shown exactly.
If the instructions in this manual are not followed correctly, malfunctions, health and life hazards, violation of laws, or voiding of legal and/or commercial warranties (if any) may occur.
Output loads must be connected to the same supply voltage as the device.
Installation
The smart Shutter Module 4C 5 A device is designed and developed to be installed in junction boxes or even in the switchboard. The design also is made to be hooked to the DIN rail located inside the junction box or in the switchboard—if it is possible.
Freedompro recommends installing the Shutter Module 4C 5 A device inside the junction box with the aim of simplifying and speeding up the installation phase because of the high probability of the presence of the wiring needed to complete the process
Connections
Danger of electrocution! Caution, changes to connections should be made only and only after making sure that there is no voltage on the terminals of the device!
Place the smart device inside a junction box or in the electrical panel, if possible attaching it to the DIN rail;
Remove the terminal covers with the help of a flathead screwdriver;
Connect the wire feeding the upward movement of the motor you want to control to terminal O1
Connect the wire feeding the downward movement of the motor you want to control to terminal O2
Connect the wire for the rise coming from the pushbutton to terminal S1
Connect the wire for the descent coming from the pushbutton to terminal S2
Connect the wires (Phase and Neutral) to terminals L and N to power the module, as shown in the diagram below;
Verify that the wiring is correct;
Reattach the covers to the terminals;
Restore power to the electrical system.
Wiring Diagram
Legend
Terminale | |
|---|---|
O1 | Load circuit output terminal 1 (Max 5 A) |
O2 | Load circuit output terminal 2 (Max 5 A) |
O3 | Load circuit output terminal 3 (Max 5 A) |
O4 | Load circuit output terminal 4 (Max 5 A) |
S1 | Switch input terminal (O1 control) |
S2 | Switch input terminal (O2 control) |
S3 | Switch input terminal (O3 control) |
S4 | Switch input terminal (O4 control) |
SC | Common switch output terminal |
L | Under voltage terminal (110-240V AC) |
N | Neutral terminal (110-240 V AC) |
How to control Shutter Module with multiple buttons to control shutters
At this point, the Shutter module is working and ready to use with the buttons just connected.
With this type of installation, it is necessary to set the command type Push Button" for the channels involved within the Freedompro app. Read the guide to set the commands by clicking on the link.
All you have to do is complete the pairing with the Freedompro app to get the most out of your Freedompro device. Follow this brief guide to find out how to pair a Freedompro device with the app.
Once you pair the module with the Freedompro app you can also complete pairing with all smart home management platforms compatible with the Freedompro ecosystem.
Choose your preferred ecosystem and integrate your Freedompro module:
Learn how to pair a Freedompro smart device with Amazon Alexa
Learn how to pair a Freedompro smart device with Apple Home
Learn how to pair a Freedompro smart device with Google Assistant
Learn how to pair a Freedompro smart device with IFTTT
Learn how to pair a Freedompro smart device with Home Assistant
Freedompro is not responsible for any loss or damage in the event of improper installation or improper operation of the device due to failure to follow the operating and safety instructions in this guide.